
Mitsubishi E3 Error: Outdoor Coil Temperature Sensor Fault
If your Mitsubishi inverter air conditioner is displaying the E3 error code, it indicates an issue with the outdoor coil temperature sensor. This problem can impact the efficiency of your AC unit and needs prompt attention. In this blog, we’ll provide a comprehensive guide to diagnosing and fixing the E3 error.
Causes of Mitsubishi E3 Error
The E3 error is typically caused by:
- Faulty Outdoor Coil Temperature Sensor: The sensor may be malfunctioning or defective.
- Wiring Issues: Problems with the wiring or connections between the sensor and the control board.
- Sensor Misalignment: The sensor may not be correctly positioned or properly attached to the outdoor coil.
- Environmental Factors: Accumulation of dirt, debris, or moisture affecting the sensor’s performance.
Detailed Solutions for E3 Error
1. Inspect and Replace the Outdoor Coil Temperature Sensor
Step-by-Step Guide:
- Turn Off the Power: Ensure the air conditioner is switched off and unplugged from the power source to ensure safety.
- Locate the Sensor: Find the outdoor coil temperature sensor, which is typically mounted on or near the outdoor coil.
- Check the Sensor: Inspect the sensor for visible damage, dirt, or debris. Use a multimeter to test the sensor’s resistance according to the manufacturer’s specifications.
- Replace the Sensor: If the sensor is defective, remove it and replace it with a new one that matches the specifications for your Mitsubishi unit.
- Reassemble and Test: Once the new sensor is installed, reassemble the unit, plug it back in, and turn it on to verify if the error has been resolved.
2. Examine and Repair Wiring Connections
Step-by-Step Guide:
- Turn Off the Power: Ensure the AC is powered off and disconnected from the electrical supply.
- Inspect Wiring: Check the wiring and connections between the outdoor coil temperature sensor and the control board. Look for any signs of damage, loose connections, or corrosion.
- Repair or Replace Wiring: Address any issues found by repairing damaged wiring with electrical tape or replacing faulty sections.
- Secure Connections: Make sure all connections are properly secured and in good condition.
- Power On and Test: Reconnect the power, turn on the air conditioner, and check if the E3 error has been cleared.
3. Realign or Adjust the Sensor
Step-by-Step Guide:
- Turn Off the Power: Switch off the air conditioner and unplug it for safety.
- Access the Sensor: Locate the outdoor coil temperature sensor and check its alignment.
- Realign the Sensor: Adjust the position of the sensor to ensure it is correctly aligned and making proper contact with the outdoor coil.
- Reassemble and Test: After realigning the sensor, reassemble the unit, plug it in, and power it on to see if the E3 error is resolved.
4. Clean the Sensor and Surrounding Area
Step-by-Step Guide:
- Turn Off the Power: Ensure the air conditioner is turned off and disconnected from the power source.
- Locate and Clean the Sensor: Find the outdoor coil temperature sensor. Use a soft brush or compressed air to remove any dust, dirt, or debris from the sensor and surrounding area.
- Reassemble and Test: Once the cleaning is complete, reassemble the unit, reconnect the power, and turn it on to check if the error persists.
Preventive Measures
To avoid future E3 errors, consider these preventive measures:
- Regular Maintenance: Schedule regular maintenance for your air conditioner to keep all components functioning properly.
- Keep the Unit Clean: Regularly clean the outdoor unit and sensor area to prevent the buildup of dirt and debris.
- Inspect Wiring Periodically: Check wiring connections periodically to detect and address any issues before they cause problems.
Conclusion
Addressing the Mitsubishi E3 error efficiently will help maintain the optimal performance of your air conditioner. If you need professional assistance, contact bulao.pk, where our expert technicians are ready to assist with all your air conditioning needs.
Contact Bulao.pk:
- Website: Bulao.pk
- Phone: 03111333318
- Email: info@bulao.pk